Re: [ECOS] ethernet initialization error

[Gary Thomas <gary at mlbassoc dot com>]

On Thu, 2005-04-07 at 12:07 +0100, Gonçalo Antunes wrote:
> On the configtool I added the FreeBsd stack, common ethernet drivers and 
> ecos http server packages.
> I configured mannually the Eth0 settings with the IP's stated below.
> The only thing that my application lauches is a thread to run the ecos http 
> server.
> The http server itself inits the network devices with the 
> init_all_network_interfaces, right?
> 
> That's all I've done...
> Is there anything more to do that I've missed?

Did you start with a target that includes the RLTK ethernet?
Does eCos even find the card?
Have you tried enabling any of the various debugging, such as I/O
initialization (to see if the card is even being probed) or ethernet
debugging (to see more of what's happening when you try and use it)?

> 
> The code for the httpd server is attached.
> 
> Thank you very much again.
> 
> Gonçalo Antunes.
> 
> 
> 
> ----- Original Message ----- 
> From: "Gary Thomas" <gary@mlbassoc.com>
> To: "Gonçalo Antunes" <gmma@gmma.net>
> Cc: "eCos Discussion" <ecos-discuss@ecos.sourceware.org>
> Sent: Thursday, April 07, 2005 11:48 AM
> Subject: Re: [ECOS] ethernet initialization error
> 
> 
> > On Thu, 2005-04-07 at 11:44 +0100, Gonçalo Antunes wrote:
> >> Hello!
> >>
> >> I'm doing some tests with  my eCos application that will run with network
> >> support on a i386 pc with a Realtek PCI network adapter.
> >> I've added the FreeBSD network stack and configured the Eth0 settings.
> >> When trying to get up the init_all_network_interfaces I get the following
> >> error.
> >> Can you help?
> >>
> >>
> >> BOOTP[eth0] op: REPLY
> >> >>           htype: Ethernet
> >> >>            hlen: 6
> >> >>            hops: 0
> >> >>             xid: 0x0
> >> >>            secs: 0
> >> >>           flags: 0x0
> >> >>         hw_addr: ff:ff:ff:ff:ff:ff
> >> >>        client IP: 192.168.0.200
> >> >>           my IP: 192.168.0.200
> >> >>       server IP: 192.168.0.1
> >> >>      gateway IP: 192.168.0.1
> >> >>
> >> >>      options:
> >> >>            subnet mask: 255.255.255.0
> >> >>           IP broadcast: 192.168.0.255
> >> >>                gateway: 192.168.0.1
> >> >>    SIOCIFADDR: Device not configured
> >> >>    Network initialization failed for eth0
> >
> > You've not told us enough to be able to comment.
> >
> > How did you configure your system to achieve these settings?
> >
> > -- 
> > ------------------------------------------------------------
> > Gary Thomas                 |  Consulting for the
> > MLB Associates              |    Embedded world
> > ------------------------------------------------------------
> >
> >
> > -- 
> > Before posting, please read the FAQ: http://ecos.sourceware.org/fom/ecos
> > and search the list archive: http://ecos.sourceware.org/ml/ecos-discuss
> >
> > 
> -- 
> Before posting, please read the FAQ: http://ecos.sourceware.org/fom/ecos
> and search the list archive: http://ecos.sourceware.org/ml/ecos-discuss
-- 
------------------------------------------------------------
Gary Thomas                 |  Consulting for the
MLB Associates              |    Embedded world
------------------------------------------------------------


-- 
Before posting, please read the FAQ: http://ecos.sourceware.org/fom/ecos
and search the list archive: http://ecos.sourceware.org/ml/ecos-discuss