This is the mail archive of the
gdb-patches@sourceware.org
mailing list for the GDB project.
Re: Watchpoint on an unloaded shared library(1)
- From: Emi SUZUKI <emi-suzuki at tjsys dot co dot jp>
- To: brobecker at adacore dot com
- Cc: gdb-patches at sourceware dot org
- Date: Tue, 06 Jan 2009 10:47:17 +0900 (JST)
- Subject: Re: Watchpoint on an unloaded shared library(1)
- References: <20081226061055.GA4216@adacore.com> <20081226.160820.01367812.emi-suzuki@tjsys.co.jp> <20081228111719.GC4216@adacore.com>
Hello Joel,
From: Joel Brobecker <brobecker at adacore.com>
Subject: Re: Watchpoint on an unloaded shared library(1)
Date: Sun, 28 Dec 2008 15:17:19 +0400
> However, you did not say whether you tested the change (meaning that
> you verified that it does not introduce any new failure in the GDB
> testsuite), and if you did, on which system. I just want to make
> sure the change was properly tested before it is checked in.
OK, I would mention it from now on.
>> + struct gdb_exception e;
>> + TRY_CATCH (e, RETURN_MASK_ALL)
>
> Can you add an empty line between these two line. The style in GDB
> is to separate the local variable declarations from the rest of
> the code by an empty line.
The below is the reviced one. I've tested it on x86-linux (F9) and
seen no regression.
Thank you for all of your valuable advices for this issue!
2008-12-26 Joel Brobecker <brobecker@adacore.com>
Emi Suzuki <emi-suzuki@tjsys.co.jp>
* breakpoint.c (do_enable_breakpoint): Use update_watchpoint for
watchpoints.
--- breakpoint.c.orig 2009-01-03 14:57:50.000000000 +0900
+++ breakpoint.c 2009-01-05 14:34:01.000000000 +0900
@@ -7789,56 +7789,18 @@ do_enable_breakpoint (struct breakpoint
bpt->type == bp_read_watchpoint ||
bpt->type == bp_access_watchpoint)
{
- struct frame_id saved_frame_id;
-
- saved_frame_id = get_frame_id (get_selected_frame (NULL));
- if (bpt->exp_valid_block != NULL)
+ struct gdb_exception e;
+
+ TRY_CATCH (e, RETURN_MASK_ALL)
{
- struct frame_info *fr =
- fr = frame_find_by_id (bpt->watchpoint_frame);
- if (fr == NULL)
- {
- printf_filtered (_("\
-Cannot enable watchpoint %d because the block in which its expression\n\
-is valid is not currently in scope.\n"), bpt->number);
- return;
- }
- select_frame (fr);
+ update_watchpoint (bpt, 1 /* reparse */);
}
-
- if (bpt->val)
- value_free (bpt->val);
- mark = value_mark ();
- fetch_watchpoint_value (bpt->exp, &bpt->val, NULL, NULL);
- if (bpt->val)
- release_value (bpt->val);
- bpt->val_valid = 1;
-
- if (bpt->type == bp_hardware_watchpoint ||
- bpt->type == bp_read_watchpoint ||
- bpt->type == bp_access_watchpoint)
+ if (e.reason < 0)
{
- int i = hw_watchpoint_used_count (bpt->type, &other_type_used);
- int mem_cnt = can_use_hardware_watchpoint (bpt->val);
-
- /* Hack around 'unused var' error for some targets here */
- (void) mem_cnt, (void) i;
- target_resources_ok = TARGET_CAN_USE_HARDWARE_WATCHPOINT (
- bpt->type, i + mem_cnt, other_type_used);
- /* we can consider of type is bp_hardware_watchpoint, convert to
- bp_watchpoint in the following condition */
- if (target_resources_ok < 0)
- {
- printf_filtered (_("\
-Cannot enable watchpoint %d because target watch resources\n\
-have been allocated for other watchpoints.\n"), bpt->number);
- value_free_to_mark (mark);
- return;
- }
+ exception_fprintf (gdb_stderr, e, _("Cannot enable watchpoint %d: "),
+ bpt->number);
+ return;
}
-
- select_frame (frame_find_by_id (saved_frame_id));
- value_free_to_mark (mark);
}
if (bpt->enable_state != bp_permanent)
My best regards,
--
Emi SUZUKI / emi-suzuki at tjsys.co.jp