Re: Using gdb with JEENI

[Fernando Nasser <fnasser at cygnus dot com>]

Jeremy Lin wrote:
> 
> It is cygwin 1.1, I installed in in August 2000.
> Thanks!
> 

Jeremy,

I am not completely sure about this specific Cygwin version, but people have
been getting good results with more recent versions.  Maybe you should
try upgrading to a recent Cygwin snapshot.

Fernando


> Jeremy Lin
> 
> --- Fernando Nasser <fnasser@cygnus.com> wrote:
> > Which version of Cygwin are you using?
> >
> > Jeremy Lin wrote:
> > >
> > > I have a problem using JEENI with GDB 5.0 debugging.
> > > JEENI FirmwareVersion:2.0
> > > Connected via serial port and RDI(tar rdi s=com2),
> > > I'm doing the eCos porting to our customize board based on
> > > Samsung KS32C50100 (ARM7TDMI core). Right now I'm debugging
> > > the ROM image which initialize the board. The problem is, for example,
> > > here is a sample instructions of the ROM image dump by gnu objdump:
> > > 00008060 <reset_vector>:
> > >     8060:       e59f0458        ldr     r0, [pc, #458]
> > >     8064:       e5800000        str     r0, [r0]
> > >
> > > 00008068 <warm_reset>:
> > >     8068:       e3a00000        mov     r0, #0  ; 0x0
> > >     806c:       e5800040        str     r0, [r0, #64]
> > >     8070:       e59f144c        ldr     r1, [pc, #44c]
> > >     8074:       e5912008        ldr     r2, [r1, #8]
> > >     8078:       e5802008        str     r2, [r0, #8]
> > >     807c:       e5912040        ldr     r2, [r1, #64]
> > >     8080:       e5802028        str     r2, [r0, #40]
> > >     8084:       ef000000        swi     0x00000000
> > >
> > > when I set a breakpoint"b *0x8070" then "continue", it breaks
> > > normally. But after that I type "stepi" to run next instruction.
> > > This message comes out and gdb was terminated:
> > >
> > > 0 [main] arm-elf-gdb 1003 handle_exceptions: Exception: \
> > > STATUS_ACCESS_VIOLATION
> > > 21532 [main] arm-elf-gdb 1003 stackdump: Dumping stack trace to
> > > arm-elf-gdb.exe.stack.dump
> > > Segmentation fault (core dump)
> > >
> > > This happens also when I set the 2nd breakpoint (for example, at 0x8080)
> > and
> > > enter "continue". So I can only set one breakpoint at a time...
> > > Does any one have the same problem?
> > >
> > > __________________________________________________
> > > Do You Yahoo!?
> > > Get email at your own domain with Yahoo! Mail.
> > > http://personal.mail.yahoo.com/
> >
> > --
> > Fernando Nasser
> > Red Hat - Toronto                       E-Mail:  fnasser@redhat.com
> > 2323 Yonge Street, Suite #300
> > Toronto, Ontario   M4P 2C9
> 
> __________________________________________________
> Do You Yahoo!?
> Get email at your own domain with Yahoo! Mail.
> http://personal.mail.yahoo.com/

-- 
Fernando Nasser
Red Hat - Toronto                       E-Mail:  fnasser@redhat.com
2323 Yonge Street, Suite #300
Toronto, Ontario   M4P 2C9