This is the mail archive of the
libc-alpha@sources.redhat.com
mailing list for the glibc project.
Re: [PATCH] powerpc64 config pass 3
- From: Daniel Jacobowitz <drow at mvista dot com>
- To: Steve Munroe <sjmunroe at vnet dot ibm dot com>
- Cc: libc-alpha at sources dot redhat dot com, aj at suse dot de, geoffk at geoffk dot org,roland at frob dot com
- Date: Fri, 30 Aug 2002 16:39:44 -0400
- Subject: Re: [PATCH] powerpc64 config pass 3
- References: <200208302027.g7UKRWs20915@brule.rchland.ibm.com>
On Fri, Aug 30, 2002 at 03:27:32PM -0500, Steve Munroe wrote:
> Same as before but with:
>
> With script changes so that both versions of setjmp.S and __longjmp.S
> get moved to correct directories.
>
> The base directory moves and configuration patches for powerpc64 follow.
>
> First a bash script (ppc64dirclean-23.sh) is provides to create the
> powerpc32 and powerpc64 directories and move powerpc 32-bit specific
> code in the appropriate ./powerpc32 directory.
>
> Next a patch (ppc64-config-20020829.patch) that applies the required
> configuration (Dist, Implies, Makefile, and Versions) changes to enable
> powerpc64 and support the exiting powerpc32 code in its new directory
> structure.
>
> Finally a patch (ppc64-configpthread-20020829.patch) that applies
> similar changes for linuxthreads. The directory creates and powerpc32
> specific code moves were done by the previously mentioned script.
>
> I tested these (script and patches) against the cvs tip pulled yesterday.
> I was able to configure and build a powerpc32 glibc without error and
> run "make check". Make check ran with the same five failures (test-float,
> test-double, test-ifloat.out, test-idouble, tfformat) as without this
> patch.
>
> Applying this patch will allow incremental submittion of the powerpc64
> changles with minimul impact on powerpc32 and other architectures.
>
> Thanks for all your help.
>
> 2002-07-29 Steven Munroe <sjmunroe@us.ibm.com>
>
> * sysdeps/powerpc/__longjmp.S: Moved to...
> * sysdeps/powerpc/powerpc32/__longjmp.S: ...here.
This isn't right. Let's try again: The only reason to put something
under powerpc32/ is if it is more appropriate for there to be _no_
implementation on powerpc64. I assume powerpc64 supports __longjmp, so
you should just be creating sysdeps/powerpc/powerpc64/__longjmp.S.
I'm not sure about the fpu/ versions but I don't think moving them is
right either.
> * sysdeps/powerpc/add_n.S: Moved to...
> * sysdeps/powerpc/powerpc32/add_n.S: ...here.
> * sysdeps/powerpc/addmul_1.S: Moved to...
> * sysdeps/powerpc/powerpc32/addmul_1.S: ...here.
> * sysdeps/powerpc/atomicity.h: Moved to...
> * sysdeps/powerpc/powerpc32/atomicity.h: ...here.
> * sysdeps/powerpc/backtrace.c: Moved to...
> * sysdeps/powerpc/powerpc32/backtrace.c: ...here.
> * sysdeps/powerpc/bp-asm.h: Moved to...
> * sysdeps/powerpc/powerpc32/bp-asm.h: ...here.
> * sysdeps/powerpc/bsd-_setjmp.S: Moved to...
> * sysdeps/powerpc/powerpc32/bsd-_setjmp.S: ...here.
> * sysdeps/powerpc/bsd-setjmp.S: Moved to...
> * sysdeps/powerpc/powerpc32/bsd-setjmp.S: ...here.
> * sysdeps/powerpc/dl-machine.c: Moved to...
> * sysdeps/powerpc/powerpc32/dl-machine.c: ...here.
> * sysdeps/powerpc/dl-machine.h: Moved to...
> * sysdeps/powerpc/powerpc32/dl-machine.h: ...here.
> * sysdeps/powerpc/dl-start.S: Moved to...
> * sysdeps/powerpc/powerpc32/dl-start.S: ...here.
> * sysdeps/powerpc/gprrest0.S: Moved to...
> * sysdeps/powerpc/powerpc32/gprrest0.S: ...here.
> * sysdeps/powerpc/gprrest1.S: Moved to...
> * sysdeps/powerpc/powerpc32/gprrest1.S: ...here.
> * sysdeps/powerpc/gprsave0.S: Moved to...
> * sysdeps/powerpc/powerpc32/gprsave0.S: ...here.
> * sysdeps/powerpc/gprsave1.S: Moved to...
> * sysdeps/powerpc/powerpc32/gprsave1.S: ...here.
> * sysdeps/powerpc/lshift.S: Moved to...
> * sysdeps/powerpc/powerpc32/lshift.S: ...here.
> * sysdeps/powerpc/memset.S: Moved to...
> * sysdeps/powerpc/powerpc32/memset.S: ...here.
> * sysdeps/powerpc/mul_1.S: Moved to...
> * sysdeps/powerpc/powerpc32/mul_1.S: ...here.
> * sysdeps/powerpc/ppc-mcount.S: Moved to...
> * sysdeps/powerpc/powerpc32/ppc-mcount.S: ...here.
> * sysdeps/powerpc/register-dump.h: Moved to...
> * sysdeps/powerpc/powerpc32/register-dump.h: ...here.
> * sysdeps/powerpc/rshift.S: Moved to...
> * sysdeps/powerpc/powerpc32/rshift.S: ...here.
> * sysdeps/powerpc/setjmp.S: Moved to...
> * sysdeps/powerpc/powerpc32/setjmp.S: ...here.
> * sysdeps/powerpc/stpcpy.S: Moved to...
> * sysdeps/powerpc/powerpc32/stpcpy.S: ...here.
> * sysdeps/powerpc/strchr.S: Moved to...
> * sysdeps/powerpc/powerpc32/strchr.S: ...here.
> * sysdeps/powerpc/strcmp.S: Moved to...
> * sysdeps/powerpc/powerpc32/strcmp.S: ...here.
> * sysdeps/powerpc/strcpy.S: Moved to...
> * sysdeps/powerpc/powerpc32/strcpy.S: ...here.
> * sysdeps/powerpc/strlen.S: Moved to...
> * sysdeps/powerpc/powerpc32/strlen.S: ...here.
> * sysdeps/powerpc/sub_n.S: Moved to...
> * sysdeps/powerpc/powerpc32/sub_n.S: ...here.
> * sysdeps/powerpc/submul_1.S: Moved to...
> * sysdeps/powerpc/powerpc32/submul_1.S: ...here.
> * sysdeps/powerpc/elf/bzero.S: Moved to...
> * sysdeps/powerpc/powerpc32/elf/bzero.S: ...here.
> * sysdeps/powerpc/elf/start.S: Moved to...
> * sysdeps/powerpc/powerpc32/elf/start.S: ...here.
> * sysdeps/powerpc/fpu/__longjmp.S: Moved to...
> * sysdeps/powerpc/powerpc32/fpu/__longjmp.S: ...here.
> * sysdeps/powerpc/fpu/fprrest.S: Moved to...
> * sysdeps/powerpc/powerpc32/fpu/fprrest.S: ...here.
> * sysdeps/powerpc/fpu/fprsave.S: Moved to...
> * sysdeps/powerpc/powerpc32/fpu/fprsave.S: ...here.
> * sysdeps/powerpc/fpu/setjmp.S: Moved to...
> * sysdeps/powerpc/powerpc32/fpu/setjmp.S: ...here.
> * sysdeps/powerpc/fpu/s_copysign.S: Moved to...
> * sysdeps/powerpc/powerpc32/fpu/s_copysign.S: ...here.
> * sysdeps/powerpc/fpu/s_copysignf.S: Moved to...
> * sysdeps/powerpc/powerpc32/fpu/s_copysignf.S: ...here.
> * sysdeps/unix/sysv/linux/powerpc/brk.S: Moved to...
> * sysdeps/unix/sysv/linux/powerpc/powerpc32/brk.S: ...here.
> * sysdeps/unix/sysv/linux/powerpc/clone.S: Moved to...
> * sysdeps/unix/sysv/linux/powerpc/powerpc32/clone.S: ...here.
> * sysdeps/unix/sysv/linux/powerpc/glob64.c: Moved to...
> * sysdeps/unix/sysv/linux/powerpc/powerpc32/glob64.c: ...here.
> * sysdeps/unix/sysv/linux/powerpc/kernel_stat.h: Moved to...
> * sysdeps/unix/sysv/linux/powerpc/powerpc32/kernel_stat.h: ...here.
> * sysdeps/unix/sysv/linux/powerpc/socket.S: Moved to...
> * sysdeps/unix/sysv/linux/powerpc/powerpc32/socket.S: ...here.
> * sysdeps/unix/sysv/linux/powerpc/sysdep.h: Moved to...
> * sysdeps/unix/sysv/linux/powerpc/powerpc32/sysdep.h: ...here.
> * sysdeps/unix/sysv/linux/powerpc/syscalls.list: Moved to...
> * sysdeps/unix/sysv/linux/powerpc/powerpc32/syscalls.list: ...here.
> Support PowerPC64. Separate powerpc into powerpc/powerpc32 and
> powerpc/powerpc64.
>
> >>>>>>> ppc64dirclean-23.sh
> #! /bin/bash
>
> # split ./linuxthreads/sysdeps/powerpc into powerpc32 and powerpc64
> # directories and move powerpc32 specific source files from ./powerpc/ up
> # to ./powerpc/powerpc32.
> #
> mkdir ./linuxthreads/sysdeps/powerpc/powerpc32
> mkdir ./linuxthreads/sysdeps/powerpc/powerpc64
>
> mv ./linuxthreads/sysdeps/powerpc/pt-machine.h \
> ./linuxthreads/sysdeps/powerpc/powerpc32
>
> # split ./sysdeps/powerpc into powerpc32 and powerpc64 directories and
> # move powerpc32 specific specific source files from ./powerpc/ up to
> # ./powerpc/powerpc32.
>
> mkdir ./sysdeps/powerpc/powerpc32
> mkdir ./sysdeps/powerpc/powerpc64
>
> mv ./sysdeps/powerpc/__longjmp.S ./sysdeps/powerpc/powerpc32
> mv ./sysdeps/powerpc/atomicity.h ./sysdeps/powerpc/powerpc32
> mv ./sysdeps/powerpc/backtrace.c ./sysdeps/powerpc/powerpc32
> mv ./sysdeps/powerpc/bp-asm.h ./sysdeps/powerpc/powerpc32
> mv ./sysdeps/powerpc/bsd-_setjmp.S ./sysdeps/powerpc/powerpc32
> mv ./sysdeps/powerpc/bsd-setjmp.S ./sysdeps/powerpc/powerpc32
> mv ./sysdeps/powerpc/dl-machine.c ./sysdeps/powerpc/powerpc32
> mv ./sysdeps/powerpc/dl-machine.h ./sysdeps/powerpc/powerpc32
> mv ./sysdeps/powerpc/memset.S ./sysdeps/powerpc/powerpc32
> mv ./sysdeps/powerpc/ppc-mcount.S ./sysdeps/powerpc/powerpc32
> mv ./sysdeps/powerpc/register-dump.h ./sysdeps/powerpc/powerpc32
> mv ./sysdeps/powerpc/setjmp.S ./sysdeps/powerpc/powerpc32
> mv ./sysdeps/powerpc/stpcpy.S ./sysdeps/powerpc/powerpc32
> mv ./sysdeps/powerpc/strchr.S ./sysdeps/powerpc/powerpc32
> mv ./sysdeps/powerpc/strcmp.S ./sysdeps/powerpc/powerpc32
> mv ./sysdeps/powerpc/strcpy.S ./sysdeps/powerpc/powerpc32
> mv ./sysdeps/powerpc/strlen.S ./sysdeps/powerpc/powerpc32
>
> # some files are not used by powerpc64 and only need to be moved
> # up to the powerpc32 directory. For example the assembler multiple
> # percision integer code is there to support soft_fp. Since all
> # powerpc64 implementations have hardware_fp they are not required for
> # powerpc64.
>
> mv ./sysdeps/powerpc/dl-start.S ./sysdeps/powerpc/powerpc32
> mv ./sysdeps/powerpc/add_n.S ./sysdeps/powerpc/powerpc32
> mv ./sysdeps/powerpc/addmul_1.S ./sysdeps/powerpc/powerpc32
> mv ./sysdeps/powerpc/divdi3.c ./sysdeps/powerpc/powerpc32
> mv ./sysdeps/powerpc/libgcc-compat.S ./sysdeps/powerpc/powerpc32
> mv ./sysdeps/powerpc/lshift.S ./sysdeps/powerpc/powerpc32
> mv ./sysdeps/powerpc/mul_1.S ./sysdeps/powerpc/powerpc32
> mv ./sysdeps/powerpc/rshift.S ./sysdeps/powerpc/powerpc32
> mv ./sysdeps/powerpc/sub_n.S ./sysdeps/powerpc/powerpc32
> mv ./sysdeps/powerpc/submul_1.S ./sysdeps/powerpc/powerpc32
>
> # Also gcc 3.2 for powerpc64 provides gpr save/restore functions
> # required by the ABI. So glibc does not need to supply them for powerpc64.
>
> mv ./sysdeps/powerpc/gprrest0.S ./sysdeps/powerpc/powerpc32
> mv ./sysdeps/powerpc/gprrest1.S ./sysdeps/powerpc/powerpc32
> mv ./sysdeps/powerpc/gprsave0.S ./sysdeps/powerpc/powerpc32
> mv ./sysdeps/powerpc/gprsave1.S ./sysdeps/powerpc/powerpc32
>
> # split ./sysdeps/powerpc/elf into powerpc32/elf and powerpc64/elf
> # directories and move powerpc32specific source files from ./powerpc/elf
> # up to ./powerpc/powerpc32/elf.
> #
>
> mkdir ./sysdeps/powerpc/powerpc32/elf
> mkdir ./sysdeps/powerpc/powerpc64/elf
>
> mv ./sysdeps/powerpc/elf/bzero.S ./sysdeps/powerpc/powerpc32/elf
> mv ./sysdeps/powerpc/elf/start.S ./sysdeps/powerpc/powerpc32/elf
>
> # split ./sysdeps/powerpc/fpu into powerpc32/fpu and powerpc64/fpu
> # directories and move powerpc32 specific source files from ./powerpc/fpu
> # up to ./powerpc/powerpc32/fpu. Makefile files
> # that contain a mix or powerpc common and powerpc32 specific content
> # are copied and will be patched later.
> #
>
> mkdir ./sysdeps/powerpc/powerpc32/fpu
> mkdir ./sysdeps/powerpc/powerpc64/fpu
>
> mv ./sysdeps/powerpc/fpu/__longjmp.S ./sysdeps/powerpc/powerpc32/fpu
> mv ./sysdeps/powerpc/fpu/fprrest.S ./sysdeps/powerpc/powerpc32/fpu
> mv ./sysdeps/powerpc/fpu/fprsave.S ./sysdeps/powerpc/powerpc32/fpu
> mv ./sysdeps/powerpc/fpu/setjmp.S ./sysdeps/powerpc/powerpc32/fpu
> mv ./sysdeps/powerpc/fpu/s_copysign.S ./sysdeps/powerpc/powerpc32/fpu
> mv ./sysdeps/powerpc/fpu/s_copysignf.S ./sysdeps/powerpc/powerpc32/fpu
>
> # split ./sysdeps/unix/sysv/linux/powerpc into powerpc32 and
> # powerpc64 subdirectories and move powerpc32 specific source files
> # from ./powerpc up to ./powerpc/powerpc32.
>
> mkdir ./sysdeps/unix/sysv/linux/powerpc/powerpc32
> mkdir ./sysdeps/unix/sysv/linux/powerpc/powerpc64
>
> mv ./sysdeps/unix/sysv/linux/powerpc/syscalls.list \
> ./sysdeps/unix/sysv/linux/powerpc/powerpc32/
>
> mv ./sysdeps/unix/sysv/linux/powerpc/brk.S \
> ./sysdeps/unix/sysv/linux/powerpc/powerpc32/
>
> mv ./sysdeps/unix/sysv/linux/powerpc/clone.S \
> ./sysdeps/unix/sysv/linux/powerpc/powerpc32/
>
> mv ./sysdeps/unix/sysv/linux/powerpc/kernel_stat.h \
> ./sysdeps/unix/sysv/linux/powerpc/powerpc32/
>
> mv ./sysdeps/unix/sysv/linux/powerpc/socket.S \
> ./sysdeps/unix/sysv/linux/powerpc/powerpc32/
>
> mv ./sysdeps/unix/sysv/linux/powerpc/sysdep.h \
> ./sysdeps/unix/sysv/linux/powerpc/powerpc32/
> <<<<<<< ppc64dirclean-23.sh
>
>
> 2002-07-29 Steven Munroe <sjmunroe@us.ibm.com>
>
> * FAQ.in: Add powerpc64 to supported targets list. Also state the
> minimum gcc version is 3.2
> * README: Add powerpc64 to supported targets list.
> * configure.in: Change machine=powerpc to machine=powerpc/powerpc32.
> Add powerpc64 and machine=powerpc/powerpc64.
> (HAVE_ASM_GLOBAL_DOT_NAME): Define if linux*powerpc/powerpc64*.
> * shlib-versions: Set DEFAULT version to 2.2.5 for powerpc64.
> * sysdeps/powerpc/Dist: Remove dl-machine.c, dl-start.S, ppc-mcount.S,
> gprsave1.S, gprsave0.S, gprrest1.S, and gprrest0.S.
> * sysdeps/powerpc/powerpc32/Dist: New file.
> * sysdeps/powerpc/Implies: Remove wordsize-32 and powerpc/soft-fp.
> * sysdeps/powerpc/powerpc32/Implies: New file.
> * sysdeps/powerpc/Makefile(cflags): Remove powerpc32 specific cflags.
> ($(with-fp) = no): Move test to powerpc32/Makefile.
> ($(subdir) = misc): Move to powerpc32/Makefile.
> ($(build-shared) = yes): Move to powerpc32/Makefile.
> ($(subdir) = csu): Move to powerpc32/Makefile.
> (sysdep-rtld-routines): Remove dl-start. Moved these bits to ...
> * sysdeps/powerpc/powerpc32/Makefile: New file.
> * sysdeps/powerpc/Versions: Remove libgcc functions.
> * sysdeps/powerpc/powerpc32/Versions: New file.
> * sysdeps/powerpc/fpu/Makefile: Remove fprsave and fprrest.
> * sysdeps/powerpc/powerpc32/fpu/Makefile: New file.
> * sysdeps/unix/sysv/linux/configure.in (powerpc*):
> Set arch_minimum_kernel=2.4.19 for powerpc/powerpc64. Also set
> libc_cv_gcc_unwind_find_fde=yes only if !powerpc/powerpc64.
> ($machine): Add powerpc/powerpc64 to if ... | for
> libc_cv_slibdir=/libc64.
> (powerpc*): Set ldd_rewrite_script.
> * sysdeps/unix/sysv/linux/powerpc/ldd-rewrite.sed: New file.
> * sysdeps/unix/sysv/linux/kernel-features.h [!__powerpc64__]
> (__ASSUME_TRUNCATE64_SYSCALL, __ASSUME_STAT64_SYSCALL, __ASSUME_IPC64,
> __ASSUME_FCNTL64, __ASSUME_MMAP2_SYSCALL): Macros defined.
> Deselect features that are redundant on powerpc64.
> * sysdeps/unix/sysv/linux/powerpc/Dist: Remove clone.S.
> * sysdeps/unix/sysv/linux/powerpc/powerpc32/Dist: New file.
> Add clone.S.
> * sysdeps/unix/sysv/linux/powerpc/Makefile: Remove oldgetrlimit64.
> * sysdeps/unix/sysv/linux/powerpc/powerpc32/Makefile : New file.
> * sysdeps/unix/sysv/linux/powerpc/Versions: Remove GLIBC_2.0
> functions. Remove GLIBC_2.2 functions except getrlimit and
> setrlimit. Moved them to ...
> * sysdeps/unix/sysv/linux/powerpc/powerpc32/Versions: New file.
>
> >>>>>>>> ppc64-config-20020829.patch
> diff -rc2PN -x*orig libc23-cvstip-20020828/FAQ.in libc23/FAQ.in
> *** libc23-cvstip-20020828/FAQ.in Sun May 19 13:37:21 2002
> --- libc23/FAQ.in Wed Aug 28 15:11:20 2002
> ***************
> *** 31,34 ****
> --- 31,35 ----
> alpha*-*-linux-gnu Linux-2.x on DEC Alpha
> powerpc-*-linux-gnu Linux and MkLinux on PowerPC systems
> + powerpc64-*-linux-gnu Linux-2.4+ on 64-bit PowerPC systems
> sparc-*-linux-gnu Linux-2.x on SPARC
> sparc64-*-linux-gnu Linux-2.x on UltraSPARC
> ***************
> *** 101,104 ****
> --- 102,110 ----
> of all the other tools, of course). See also ?excpt.
>
> + ??powerpc64 Which compiler should I use for powerpc64?
> +
> + {SM} You want to use at least gcc 3.2 (together with the right versions
> + of all the other tools, of course).
> +
> ??arm Which tools should I use for ARM?
>
> ***************
> *** 1669,1672 ****
> --- 1675,1679 ----
> {AO} Alexandre Oliva, <aoliva@redhat.com>
> {BH} Bruno Haible, <haible@clisp.cons.org>
> + {SM} Steven Munroe, <sjmunroe@us.ibm.com>
>
> Local Variables:
> diff -rc2PN -x*orig libc23-cvstip-20020828/README libc23/README
> *** libc23-cvstip-20020828/README Wed Aug 28 06:38:46 2002
> --- libc23/README Wed Aug 28 15:11:20 2002
> ***************
> *** 11,14 ****
> --- 11,15 ----
> alpha*-*-linux-gnu Linux-2.x on DEC Alpha
> powerpc-*-linux-gnu Linux and MkLinux on PowerPC systems
> + powerpc64-*-linux-gnu Linux-2.4+ on 64-bit PowerPC systems
> sparc-*-linux-gnu Linux-2.x on SPARC
> sparc64-*-linux-gnu Linux-2.x on UltraSPARC 64-bit
> diff -rc2PN -x*orig libc23-cvstip-20020828/configure.in libc23/configure.in
> *** libc23-cvstip-20020828/configure.in Wed Aug 28 06:32:27 2002
> --- libc23/configure.in Wed Aug 28 15:11:20 2002
> ***************
> *** 314,317 ****
> --- 314,319 ----
> mips64*) base_machine=mips64 machine=mips/mips64/$machine ;;
> mips*) base_machine=mips machine=mips/$machine ;;
> + powerpc) base_machine=powerpc machine=powerpc/powerpc32 ;;
> + powerpc64) base_machine=powerpc machine=powerpc/powerpc64 ;;
> s390) base_machine=s390 machine=s390/s390-32 ;;
> s390x) base_machine=s390 machine=s390/s390-64 ;;
> ***************
> *** 896,901 ****
>
> # The Aix ld uses global .symbol_names instead of symbol_names.
> ! case "$os" in
> ! aix4.3*)
> AC_DEFINE(HAVE_ASM_GLOBAL_DOT_NAME)
> esac
> --- 898,904 ----
>
> # The Aix ld uses global .symbol_names instead of symbol_names.
> ! # So does powerpc64-linux
> ! case "${os}${machine}" in
> ! aix4.3* | linux*powerpc/powerpc64*)
> AC_DEFINE(HAVE_ASM_GLOBAL_DOT_NAME)
> esac
> diff -rc2PN -x*orig libc23-cvstip-20020828/shlib-versions libc23/shlib-versions
> *** libc23-cvstip-20020828/shlib-versions Tue Jun 11 18:03:18 2002
> --- libc23/shlib-versions Wed Aug 28 15:11:20 2002
> ***************
> *** 25,28 ****
> --- 25,29 ----
> cris-.*-linux.* DEFAULT GLIBC_2.2
> x86_64-.*-linux.* DEFAULT GLIBC_2.2.5
> + powerpc64-.*-linux.* DEFAULT GLIBC_2.3
> .*-.*-gnu-gnu.* DEFAULT GLIBC_2.2.6
>
> ***************
> *** 70,73 ****
> --- 71,75 ----
> hppa.*-.*-.* ld=ld.so.1 GLIBC_2.2
> s390x-.*-linux.* ld=ld64.so.1 GLIBC_2.2
> + powerpc64.*-.*-linux.* ld=ld64.so.1 GLIBC_2.3
> cris-.*-linux.* ld=ld.so.1 GLIBC_2.2
> x86_64-.*-linux.* ld=ld-linux-x86-64.so.2 GLIBC_2.2.5
> diff -rc2PN -x*orig libc23-cvstip-20020828/sysdeps/powerpc/Dist libc23/sysdeps/powerpc/Dist
> *** libc23-cvstip-20020828/sysdeps/powerpc/Dist Wed Aug 28 03:29:48 2002
> --- libc23/sysdeps/powerpc/Dist Wed Aug 28 15:12:45 2002
> ***************
> *** 1,10 ****
> - divdi3.c
> - dl-machine.c
> - dl-start.S
> - libgcc-compat.S
> - ppc-mcount.S
> - gprsave1.S
> - gprsave0.S
> - gprrest1.S
> - gprrest0.S
> bp-asm.h
> --- 1 ----
> diff -rc2PN -x*orig libc23-cvstip-20020828/sysdeps/powerpc/powerpc32/Dist libc23/sysdeps/powerpc/powerpc32/Dist
> *** libc23-cvstip-20020828/sysdeps/powerpc/powerpc32/Dist Wed Dec 31 18:00:00 1969
> --- libc23/sysdeps/powerpc/powerpc32/Dist Wed Aug 28 15:12:36 2002
> ***************
> *** 0 ****
> --- 1,9 ----
> + divdi3.c
> + dl-machine.c
> + dl-start.S
> + libgcc-compat.S
> + ppc-mcount.S
> + gprsave1.S
> + gprsave0.S
> + gprrest1.S
> + gprrest0.S
> diff -rc2PN -x*orig libc23-cvstip-20020828/sysdeps/powerpc/Implies libc23/sysdeps/powerpc/Implies
> *** libc23-cvstip-20020828/sysdeps/powerpc/Implies Tue Sep 5 10:04:33 2000
> --- libc23/sysdeps/powerpc/Implies Wed Aug 28 15:11:20 2002
> ***************
> *** 1,4 ****
> - wordsize-32
> ieee754/flt-32
> ieee754/dbl-64
> - powerpc/soft-fp
> --- 1,2 ----
> diff -rc2PN -x*orig libc23-cvstip-20020828/sysdeps/powerpc/powerpc32/Implies libc23/sysdeps/powerpc/powerpc32/Implies
> *** libc23-cvstip-20020828/sysdeps/powerpc/powerpc32/Implies Wed Dec 31 18:00:00 1969
> --- libc23/sysdeps/powerpc/powerpc32/Implies Wed Aug 28 15:11:20 2002
> ***************
> *** 0 ****
> --- 1,2 ----
> + wordsize-32
> + powerpc/soft-fp
> diff -rc2PN -x*orig libc23-cvstip-20020828/sysdeps/powerpc/Makefile libc23/sysdeps/powerpc/Makefile
> *** libc23-cvstip-20020828/sysdeps/powerpc/Makefile Tue Aug 20 16:26:56 2002
> --- libc23/sysdeps/powerpc/Makefile Wed Aug 28 15:11:20 2002
> ***************
> *** 1,11 ****
> # We always want to use the new mnemonic syntax even if we are on a RS6000
> # machine.
> ! +cflags += -mnew-mnemonics -Wa,-mppc -mpowerpc
> ! asm-CPPFLAGS += -Wa,-mppc
> !
> ! ifeq ($(with-fp),no)
> ! +cflags += -msoft-float
> ! sysdep-LDFLAGS += -msoft-float
> ! endif
>
> ifeq ($(subdir),gmon)
> --- 1,7 ----
> + # Build options common to powerpc32 and powerpc64
> + # This is ./sysdeps/powerpc/Makefile
> # We always want to use the new mnemonic syntax even if we are on a RS6000
> # machine.
> ! +cflags += -mnew-mnemonics
>
> ifeq ($(subdir),gmon)
> ***************
> *** 13,50 ****
> endif
>
> - ifeq ($(subdir),misc)
> - sysdep_routines += gprsave0 gprrest0 gprsave1 gprrest1
> - endif
> -
> - # On PPC, -fpic works until the GOT contains 2^15 bytes, and possibly
> - # more depending on how clever the linker is. Each GOT entry takes 4 bytes,
> - # so that's at least 8192 entries. Since libc only uses about 2000 entries,
> - # we want to use -fpic, because this generates fewer relocs.
> - ifeq (yes,$(build-shared))
> - pic-ccflag = -fpic
> - endif
> -
> - ifeq ($(subdir),csu)
> - ifneq ($(elf),no)
> - # The initfini generation code doesn't work in the presence of -fPIC, so
> - # we use -fpic instead which is much better.
> - CFLAGS-initfini.s = -g0 -fpic -O1
> -
> - # There is no benefit to using sdata for these objects, and the user
> - # of the library should be able to control what goes into sdata.
> - CFLAGS-init.o = -G0
> - CFLAGS-gmon-start.o = -G0
> - endif
> - ifeq (yes,$(build-shared))
> - # Compatibility
> - ifeq (yes,$(have-protected))
> - CPPFLAGS-divdi3.c = -DHAVE_DOT_HIDDEN
> - CPPFLAGS-libgcc-compat.S = -DHAVE_DOT_HIDDEN
> - endif
> - sysdep_routines += divdi3 libgcc-compat
> - shared-only-routines += divdi3 libgcc-compat
> - endif
> - endif
> -
> ifeq ($(subdir),string)
> CFLAGS-memcmp.c += -Wno-uninitialized
> --- 9,12 ----
> ***************
> *** 56,59 ****
> sysdep_routines += dl-machine
> # extra shared linker files to link only into dl-allobjs.so
> ! sysdep-rtld-routines += dl-machine dl-start
> endif
> --- 18,21 ----
> sysdep_routines += dl-machine
> # extra shared linker files to link only into dl-allobjs.so
> ! sysdep-rtld-routines += dl-machine
> endif
> diff -rc2PN -x*orig libc23-cvstip-20020828/sysdeps/powerpc/powerpc32/Makefile libc23/sysdeps/powerpc/powerpc32/Makefile
> *** libc23-cvstip-20020828/sysdeps/powerpc/powerpc32/Makefile Wed Dec 31 18:00:00 1969
> --- libc23/sysdeps/powerpc/powerpc32/Makefile Wed Aug 28 15:11:20 2002
> ***************
> *** 0 ****
> --- 1,49 ----
> + # Powerpc32 specific build options.
> + # this is ./sysdeps/powerpc/powerpc32/Makefile
> +
> + +cflags += -Wa,-mppc -mpowerpc
> + asm-CPPFLAGS += -Wa,-mppc
> +
> + ifeq ($(with-fp),no)
> + +cflags += -msoft-float
> + sysdep-LDFLAGS += -msoft-float
> + endif
> +
> + ifeq ($(subdir),misc)
> + sysdep_routines += gprsave0 gprrest0 gprsave1 gprrest1
> + endif
> +
> + # On PPC, -fpic works until the GOT contains 2^15 bytes, and possibly
> + # more depending on how clever the linker is. Each GOT entry takes 4 bytes,
> + # so that's at least 8192 entries. Since libc only uses about 2000 entries,
> + # we want to use -fpic, because this generates fewer relocs.
> + ifeq (yes,$(build-shared))
> + pic-ccflag = -fpic
> + endif
> +
> + ifeq ($(subdir),csu)
> + ifneq ($(elf),no)
> + # The initfini generation code doesn't work in the presence of -fPIC, so
> + # we use -fpic instead which is much better.
> + CFLAGS-initfini.s = -g0 -fpic -O1
> +
> + # There is no benefit to using sdata for these objects, and the user
> + # of the library should be able to control what goes into sdata.
> + CFLAGS-init.o = -G0
> + CFLAGS-gmon-start.o = -G0
> + endif
> + ifeq (yes,$(build-shared))
> + # Compatibility
> + ifeq (yes,$(have-protected))
> + CPPFLAGS-divdi3.c = -DHAVE_DOT_HIDDEN
> + CPPFLAGS-libgcc-compat.S = -DHAVE_DOT_HIDDEN
> + endif
> + sysdep_routines += divdi3 libgcc-compat
> + shared-only-routines += divdi3 libgcc-compat
> + endif
> + endif
> +
> + ifeq ($(subdir),elf)
> + # extra shared linker files to link only into dl-allobjs.so
> + sysdep-rtld-routines += dl-start
> + endif
> diff -rc2PN -x*orig libc23-cvstip-20020828/sysdeps/powerpc/Versions libc23/sysdeps/powerpc/Versions
> *** libc23-cvstip-20020828/sysdeps/powerpc/Versions Tue Aug 20 16:26:56 2002
> --- libc23/sysdeps/powerpc/Versions Wed Aug 28 15:11:20 2002
> ***************
> *** 1,13 ****
> - libc {
> - GLIBC_2.0 {
> - # Functions from libgcc.
> - __divdi3; __moddi3; __udivdi3; __umoddi3;
> - __cmpdi2; __ucmpdi2;
> - __ashldi3; __ashrdi3; __lshrdi3;
> - __fixdfdi; __fixunsdfdi;
> - __fixsfdi; __fixunssfdi;
> - __floatdidf; __floatdisf;
> - }
> - }
>
> libm {
> --- 1,2 ----
> ***************
> *** 15,38 ****
> # symbols used in macros from sysdeps/powerpc/bits/fenv.h
> __fe_dfl_env; __fe_enabled_env; __fe_nonieee_env; __fe_nomask_env;
> - }
> - GLIBC_2.2 {
> - # Special functions to save and restore registers used by the
> - # runtime libraries.
> - _restgpr0_13; _restgpr0_14; _restgpr0_15; _restgpr0_16; _restgpr0_17;
> - _restgpr0_18; _restgpr0_19; _restgpr0_20; _restgpr0_21; _restgpr0_22;
> - _restgpr0_22; _restgpr0_23; _restgpr0_24; _restgpr0_25; _restgpr0_26;
> - _restgpr0_27; _restgpr0_28; _restgpr0_29; _restgpr0_30; _restgpr0_31;
> - _savegpr0_13; _savegpr0_14; _savegpr0_15; _savegpr0_16; _savegpr0_17;
> - _savegpr0_18; _savegpr0_19; _savegpr0_20; _savegpr0_21; _savegpr0_22;
> - _savegpr0_22; _savegpr0_23; _savegpr0_24; _savegpr0_25; _savegpr0_26;
> - _savegpr0_27; _savegpr0_28; _savegpr0_29; _savegpr0_30; _savegpr0_31;
> - _restgpr1_13; _restgpr1_14; _restgpr1_15; _restgpr1_16; _restgpr1_17;
> - _restgpr1_18; _restgpr1_19; _restgpr1_20; _restgpr1_21; _restgpr1_22;
> - _restgpr1_22; _restgpr1_23; _restgpr1_24; _restgpr1_25; _restgpr1_26;
> - _restgpr1_27; _restgpr1_28; _restgpr1_29; _restgpr1_30; _restgpr1_31;
> - _savegpr1_13; _savegpr1_14; _savegpr1_15; _savegpr1_16; _savegpr1_17;
> - _savegpr1_18; _savegpr1_19; _savegpr1_20; _savegpr1_21; _savegpr1_22;
> - _savegpr1_22; _savegpr1_23; _savegpr1_24; _savegpr1_25; _savegpr1_26;
> - _savegpr1_27; _savegpr1_28; _savegpr1_29; _savegpr1_30; _savegpr1_31;
> }
> }
> --- 4,7 ----
> diff -rc2PN -x*orig libc23-cvstip-20020828/sysdeps/powerpc/powerpc32/Versions libc23/sysdeps/powerpc/powerpc32/Versions
> *** libc23-cvstip-20020828/sysdeps/powerpc/powerpc32/Versions Wed Dec 31 18:00:00 1969
> --- libc23/sysdeps/powerpc/powerpc32/Versions Wed Aug 28 15:11:20 2002
> ***************
> *** 0 ****
> --- 1,34 ----
> + libc {
> + GLIBC_2.0 {
> + # Functions from libgcc.
> + __divdi3; __moddi3; __udivdi3; __umoddi3;
> + __cmpdi2; __ucmpdi2;
> + __ashldi3; __ashrdi3; __lshrdi3;
> + __fixdfdi; __fixunsdfdi;
> + __fixsfdi; __fixunssfdi;
> + __floatdidf; __floatdisf;
> + }
> + }
> +
> + libm {
> + GLIBC_2.2 {
> + # Special functions to save and restore registers used by the
> + # runtime libraries.
> + _restgpr0_13; _restgpr0_14; _restgpr0_15; _restgpr0_16; _restgpr0_17;
> + _restgpr0_18; _restgpr0_19; _restgpr0_20; _restgpr0_21; _restgpr0_22;
> + _restgpr0_22; _restgpr0_23; _restgpr0_24; _restgpr0_25; _restgpr0_26;
> + _restgpr0_27; _restgpr0_28; _restgpr0_29; _restgpr0_30; _restgpr0_31;
> + _savegpr0_13; _savegpr0_14; _savegpr0_15; _savegpr0_16; _savegpr0_17;
> + _savegpr0_18; _savegpr0_19; _savegpr0_20; _savegpr0_21; _savegpr0_22;
> + _savegpr0_22; _savegpr0_23; _savegpr0_24; _savegpr0_25; _savegpr0_26;
> + _savegpr0_27; _savegpr0_28; _savegpr0_29; _savegpr0_30; _savegpr0_31;
> + _restgpr1_13; _restgpr1_14; _restgpr1_15; _restgpr1_16; _restgpr1_17;
> + _restgpr1_18; _restgpr1_19; _restgpr1_20; _restgpr1_21; _restgpr1_22;
> + _restgpr1_22; _restgpr1_23; _restgpr1_24; _restgpr1_25; _restgpr1_26;
> + _restgpr1_27; _restgpr1_28; _restgpr1_29; _restgpr1_30; _restgpr1_31;
> + _savegpr1_13; _savegpr1_14; _savegpr1_15; _savegpr1_16; _savegpr1_17;
> + _savegpr1_18; _savegpr1_19; _savegpr1_20; _savegpr1_21; _savegpr1_22;
> + _savegpr1_22; _savegpr1_23; _savegpr1_24; _savegpr1_25; _savegpr1_26;
> + _savegpr1_27; _savegpr1_28; _savegpr1_29; _savegpr1_30; _savegpr1_31;
> + }
> + }
> diff -rc2PN -x*orig libc23-cvstip-20020828/sysdeps/powerpc/fpu/Makefile libc23/sysdeps/powerpc/fpu/Makefile
> *** libc23-cvstip-20020828/sysdeps/powerpc/fpu/Makefile Thu Dec 6 17:41:32 2001
> --- libc23/sysdeps/powerpc/fpu/Makefile Wed Aug 28 15:11:20 2002
> ***************
> *** 2,6 ****
> libm-support += fenv_const fe_nomask t_sqrt
> endif
> - ifeq ($(subdir),misc)
> - sysdep_routines += fprsave fprrest
> - endif
> --- 2,3 ----
> diff -rc2PN -x*orig libc23-cvstip-20020828/sysdeps/powerpc/powerpc32/fpu/Makefile libc23/sysdeps/powerpc/powerpc32/fpu/Makefile
> *** libc23-cvstip-20020828/sysdeps/powerpc/powerpc32/fpu/Makefile Wed Dec 31 18:00:00 1969
> --- libc23/sysdeps/powerpc/powerpc32/fpu/Makefile Wed Aug 28 15:11:20 2002
> ***************
> *** 0 ****
> --- 1,3 ----
> + ifeq ($(subdir),misc)
> + sysdep_routines += fprsave fprrest
> + endif
> diff -rc2PN -x*orig libc23-cvstip-20020828/sysdeps/unix/sysv/linux/configure.in libc23/sysdeps/unix/sysv/linux/configure.in
> *** libc23-cvstip-20020828/sysdeps/unix/sysv/linux/configure.in Sun Jul 28 17:40:47 2002
> --- libc23/sysdeps/unix/sysv/linux/configure.in Wed Aug 28 15:11:20 2002
> ***************
> *** 76,81 ****
> ;;
> powerpc*)
> ! libc_cv_gcc_unwind_find_fde=yes
> ! arch_minimum_kernel=2.0.10
> ;;
> s390/s390-32)
> --- 76,85 ----
> ;;
> powerpc*)
> ! if test "$machine" = "powerpc/powerpc64"; then
> ! arch_minimum_kernel=2.4.19
> ! else
> ! libc_cv_gcc_unwind_find_fde=yes
> ! arch_minimum_kernel=2.0.10
> ! fi
> ;;
> s390/s390-32)
> ***************
> *** 152,156 ****
> if test "$prefix" = "/usr" -o "$prefix" = "/usr/"; then
> # 64bit libraries on sparc go to /lib64 and not /lib
> ! if test "$machine" = "sparc/sparc64" -o "$machine" = "x86_64"; then
> libc_cv_slibdir="/lib64"
> if test "$libdir" = '${exec_prefix}/lib'; then
> --- 156,160 ----
> if test "$prefix" = "/usr" -o "$prefix" = "/usr/"; then
> # 64bit libraries on sparc go to /lib64 and not /lib
> ! if test "$machine" = "sparc/sparc64" -o "$machine" = "x86_64" -o "$machine" = "powerpc/powerpc64" -o "$machine" = "s390/s390-64"; then
> libc_cv_slibdir="/lib64"
> if test "$libdir" = '${exec_prefix}/lib'; then
> ***************
> *** 235,238 ****
> --- 239,245 ----
> x86_64*)
> ldd_rewrite_script=../sysdeps/unix/sysv/linux/x86_64/ldd-rewrite.sed
> + ;;
> + powerpc*)
> + ldd_rewrite_script=../sysdeps/unix/sysv/linux/powerpc/ldd-rewrite.sed
> ;;
> *)
> diff -rc2PN -x*orig libc23-cvstip-20020828/sysdeps/unix/sysv/linux/powerpc/ldd-rewrite.sed libc23/sysdeps/unix/sysv/linux/powerpc/ldd-rewrite.sed
> *** libc23-cvstip-20020828/sysdeps/unix/sysv/linux/powerpc/ldd-rewrite.sed Wed Dec 31 18:00:00 1969
> --- libc23/sysdeps/unix/sysv/linux/powerpc/ldd-rewrite.sed Wed Aug 28 15:11:20 2002
> ***************
> *** 0 ****
> --- 1,15 ----
> + /LD_TRACE_LOADED_OBJECTS=1/a\
> + add_env="$add_env LD_LIBRARY_VERSION=\\$verify_out"
> +
> + # ldd is generated from elf/ldd.bash.in with the name
> + # of ld.so as generated in Makeconfig
> +
> + # that name is replaced by a pair referring to both
> + # the 32bit and 64bit dynamic linker.
> +
> + # /lib(64|)/*(64|).so* is replaced with /lib/*.so* and /lib64/*64.so*
> + # this works for /lib64/ld64.so.x and /lib/ld.so.x as input
> + s_lib64_lib_
> + s_64\.so_\.so_
> + s_^RTLDLIST=\(.*lib\)\(/[^/]*\)\(\.so\.[0-9.]*\)[[:blank:]]*$_RTLDLIST="\1\2\3 \164\264\3"_
> +
> diff -rc2PN -x*orig libc23-cvstip-20020828/sysdeps/unix/sysv/linux/kernel-features.h libc23/sysdeps/unix/sysv/linux/kernel-features.h
> *** libc23-cvstip-20020828/sysdeps/unix/sysv/linux/kernel-features.h Thu Aug 15 07:58:40 2002
> --- libc23/sysdeps/unix/sysv/linux/kernel-features.h Wed Aug 28 15:11:20 2002
> ***************
> *** 104,111 ****
> #endif
>
> ! /* I know for sure that these are in 2.3.35 on powerpc. */
> #if __LINUX_KERNEL_VERSION >= 131875 && defined __powerpc__
> ! # define __ASSUME_TRUNCATE64_SYSCALL 1
> ! # define __ASSUME_STAT64_SYSCALL 1
> # define __ASSUME_NEW_GETRLIMIT_SYSCALL 1
> #endif
> --- 104,114 ----
> #endif
>
> ! /* I know for sure that these are in 2.3.35 on powerpc. But PowerPC64 does not
> ! support a separate 64-bit syscall, already 64-bit */
> #if __LINUX_KERNEL_VERSION >= 131875 && defined __powerpc__
> ! # if !defined __powerpc64__
> ! # define __ASSUME_TRUNCATE64_SYSCALL 1
> ! # define __ASSUME_STAT64_SYSCALL 1
> ! # endif
> # define __ASSUME_NEW_GETRLIMIT_SYSCALL 1
> #endif
> ***************
> *** 123,129 ****
> #endif
>
> ! /* Linux 2.4.0 on PPC introduced a correct IPC64. */
> #if __LINUX_KERNEL_VERSION >= 132096 && defined __powerpc__
> ! # define __ASSUME_IPC64 1
> #endif
>
> --- 126,135 ----
> #endif
>
> ! /* Linux 2.4.0 on PPC introduced a correct IPC64. But PowerPC64 does not
> ! support a separate 64-bit sys call, already 64-bit */
> #if __LINUX_KERNEL_VERSION >= 132096 && defined __powerpc__
> ! # if !defined __powerpc64__
> ! # define __ASSUME_IPC64 1
> ! # endif
> #endif
>
> ***************
> *** 148,155 ****
>
> /* Arm got fcntl64 in 2.4.4, PowerPC and SH have it also in 2.4.4 (I
> ! don't know when it got introduced). */
> #if __LINUX_KERNEL_VERSION >= 132100 \
> && (defined __arm__ || defined __powerpc__ || defined __sh__)
> ! # define __ASSUME_FCNTL64 1
> #endif
>
> --- 154,164 ----
>
> /* Arm got fcntl64 in 2.4.4, PowerPC and SH have it also in 2.4.4 (I
> ! don't know when it got introduced). But PowerPC64 does not support
> ! separate FCNTL64 call, FCNTL is already 64-bit */
> #if __LINUX_KERNEL_VERSION >= 132100 \
> && (defined __arm__ || defined __powerpc__ || defined __sh__)
> ! # if !defined __powerpc64__
> ! # define __ASSUME_FCNTL64 1
> ! # endif
> #endif
>
> ***************
> *** 179,186 ****
>
> /* Starting with 2.4.5 kernels PPC passes the AUXV in the standard way
> ! and the mmap2 syscall made it into the official kernel. */
> #if __LINUX_KERNEL_VERSION >= (132096+5) && defined __powerpc__
> # define __ASSUME_STD_AUXV 1
> ! # define __ASSUME_MMAP2_SYSCALL 1
> #endif
>
> --- 188,198 ----
>
> /* Starting with 2.4.5 kernels PPC passes the AUXV in the standard way
> ! and the mmap2 syscall made it into the official kernel. But
> ! PowerPC64 does not support a separate MMAP2 call. */
> #if __LINUX_KERNEL_VERSION >= (132096+5) && defined __powerpc__
> # define __ASSUME_STD_AUXV 1
> ! # if !defined __powerpc64__
> ! # define __ASSUME_MMAP2_SYSCALL 1
> ! # endif
> #endif
>
> diff -rc2PN -x*orig libc23-cvstip-20020828/sysdeps/unix/sysv/linux/powerpc/Dist libc23/sysdeps/unix/sysv/linux/powerpc/Dist
> *** libc23-cvstip-20020828/sysdeps/unix/sysv/linux/powerpc/Dist Wed Aug 28 03:55:26 2002
> --- libc23/sysdeps/unix/sysv/linux/powerpc/Dist Wed Aug 28 15:11:20 2002
> ***************
> *** 1,3 ****
> - clone.S
> dl-brk.S
> fe_nomask.c
> --- 1,2 ----
> diff -rc2PN -x*orig libc23-cvstip-20020828/sysdeps/unix/sysv/linux/powerpc/powerpc32/Dist libc23/sysdeps/unix/sysv/linux/powerpc/powerpc32/Dist
> *** libc23-cvstip-20020828/sysdeps/unix/sysv/linux/powerpc/powerpc32/Dist Wed Dec 31 18:00:00 1969
> --- libc23/sysdeps/unix/sysv/linux/powerpc/powerpc32/Dist Wed Aug 28 15:11:20 2002
> ***************
> *** 0 ****
> --- 1,2 ----
> + clone.S
> +
> diff -rc2PN -x*orig libc23-cvstip-20020828/sysdeps/unix/sysv/linux/powerpc/Makefile libc23/sysdeps/unix/sysv/linux/powerpc/Makefile
> *** libc23-cvstip-20020828/sysdeps/unix/sysv/linux/powerpc/Makefile Sat Mar 23 19:55:18 2002
> --- libc23/sysdeps/unix/sysv/linux/powerpc/Makefile Wed Aug 28 15:11:20 2002
> ***************
> *** 3,8 ****
> rt_sigqueueinfo rt_sigaction rt_sigpending
> endif
> -
> - ifeq ($(subdir),resource)
> - sysdep_routines += oldgetrlimit64
> - endif
> --- 3,4 ----
> diff -rc2PN -x*orig libc23-cvstip-20020828/sysdeps/unix/sysv/linux/powerpc/powerpc32/Makefile libc23/sysdeps/unix/sysv/linux/powerpc/powerpc32/Makefile
> *** libc23-cvstip-20020828/sysdeps/unix/sysv/linux/powerpc/powerpc32/Makefile Wed Dec 31 18:00:00 1969
> --- libc23/sysdeps/unix/sysv/linux/powerpc/powerpc32/Makefile Wed Aug 28 15:11:20 2002
> ***************
> *** 0 ****
> --- 1,3 ----
> + ifeq ($(subdir),resource)
> + sysdep_routines += oldgetrlimit64
> + endif
> diff -rc2PN -x*orig libc23-cvstip-20020828/sysdeps/unix/sysv/linux/powerpc/Versions libc23/sysdeps/unix/sysv/linux/powerpc/Versions
> *** libc23-cvstip-20020828/sysdeps/unix/sysv/linux/powerpc/Versions Fri Aug 23 04:29:01 2002
> --- libc23/sysdeps/unix/sysv/linux/powerpc/Versions Wed Dec 31 18:00:00 1969
> ***************
> *** 1,23 ****
> - libc {
> - GLIBC_2.0 {
> - # Exception handling support functions from libgcc
> - __register_frame; __register_frame_table; __deregister_frame;
> - __frame_state_for; __register_frame_info_table;
> - }
> - GLIBC_2.2 {
> - # functions used in other libraries
> - __xstat64; __fxstat64; __lxstat64;
> -
> - # g*
> - glob64;
> -
> - # New rlimit interface
> - getrlimit; setrlimit; getrlimit64; setrlimit64;
> -
> - # r*
> - readdir64; readdir64_r;
> -
> - # s*
> - scandir64;
> - }
> - }
> --- 0 ----
> diff -rc2PN -x*orig libc23-cvstip-20020828/sysdeps/unix/sysv/linux/powerpc/powerpc32/Versions libc23/sysdeps/unix/sysv/linux/powerpc/powerpc32/Versions
> *** libc23-cvstip-20020828/sysdeps/unix/sysv/linux/powerpc/powerpc32/Versions Wed Dec 31 18:00:00 1969
> --- libc23/sysdeps/unix/sysv/linux/powerpc/powerpc32/Versions Wed Aug 28 15:11:20 2002
> ***************
> *** 0 ****
> --- 1,22 ----
> + libc {
> + GLIBC_2.0 {
> + # Exception handling support functions from libgcc
> + __register_frame; __register_frame_table; __deregister_frame;
> + __frame_state_for; __register_frame_info_table;
> + }
> + GLIBC_2.2 {
> + # functions used in other libraries
> + __xstat64; __fxstat64; __lxstat64;
> +
> + # g*
> + glob64;
> +
> + # New rlimit interface
> + getrlimit; setrlimit; getrlimit64; setrlimit64;
> +
> + # r*
> + readdir64; readdir64_r;
> +
> + # s*
> + scandir64;
> + }
> <<<<<<<< ppc64-config-20020829.patch
>
> 2002-07-29 Steven Munroe <sjmunroe@us.ibm.com>
>
> * shlib-versions: Set libpthread version to 2.2.5 for powerpc64.
> * sysdeps/powerpc/pt-machine.h: moved to...
> * sysdeps/powerpc/powerpc32/pt-machine.h: ...here
> * sysdeps/powerpc/powerpc64/pt-machine.h: New file.
>
> >>>>>>>> ppc64-configpthread-20020829.patch
> diff -rc2PN -x*orig libc23-cvstip-20020828/linuxthreads/shlib-versions libc23/linuxthreads/shlib-versions
> *** libc23-cvstip-20020828/linuxthreads/shlib-versions Thu Sep 20 01:35:08 2001
> --- libc23/linuxthreads/shlib-versions Thu Aug 29 09:53:44 2002
> ***************
> *** 8,10 ****
> --- 8,11 ----
> cris-.*-linux.* libpthread=0 GLIBC_2.2
> x86_64-.*-linux.* libpthread=0 GLIBC_2.2.5
> + powerpc64-.*-linux.* libpthread=0 GLIBC_2.3
> .*-.*-linux.* libpthread=0
> <<<<<<<< ppc64-configpthread-20020829.patch
>
--
Daniel Jacobowitz
MontaVista Software Debian GNU/Linux Developer