This is the mail archive of the pthreads-win32@sources.redhat.com mailing list for the pthreas-win32 project.


Index Nav: [Date Index] [Subject Index] [Author Index] [Thread Index]
Message Nav: [Date Prev] [Date Next] [Thread Prev] [Thread Next]

RE: [pthread-win32] Unsubscribe


It's weird to be so complicated to unsubscribe. Is there anyone
taking care of this mail list? Can't he remove me from the list?

Long

On Fri, 21 Jul 2000, Kevin D. Clark wrote:

> 
> Keith A. Jackson writes:
> 
> > Oooo. Ooo. Me too. Anyone else?
> 
> First, ask your Internet Provider to mail you an Unsubscribing Kit.  Then
> follow these directions.
> 
> The kit will most likely be the standard no-fault type. Depending on
> requirements, System A and/or System B can be used. When operating System A,
> depress lever and a plastic dalkron unsubscriber will be dispensed through
> the slot immediately underneath. When you have fastened the adhesive lip,
> attach connection marked by the large "X" outlet hose. Twist the silver-
> coloured ring one inch below the connection point until you feel it lock.
> 
> The kit is now ready for use. The Cin-Eliminator is activated by the small
> switch on the lip. When securing, twist the ring back to its initial
> condition, so that the two orange lines meet. Disconnect. Place the dalkron
> unsubscriber in the vacuum receptacle to the rear. Activate by pressing the
> blue button.
> 
> The controls for System B are located on the opposite side. The red release
> switch places the Cin-Eliminator into position; it can be adjusted manually
> up or down by pressing the blue manual release button. The opening is self-
> adjusting. To secure after use, press the green button, which simultaneously
> activates the evaporator and returns the Cin-Eliminator to its storage
> position.
> 
> You may log off if the green exit light is on over the evaporator . If the
> red light is illuminated, one of the Cin-Eliminator requirements has not been
> properly implemented. Press the "List Guy" call button on the right of the
> evaporator . He will secure all facilities from his control panel.
> 
> To use the Auto-Unsub, first undress and place all your clothes in the
> clothes rack. Put on the velcro slippers located in the cabinet immediately
> below. Enter the shower, taking the entire kit with you. On the control panel
> to your upper right upon entering you will see a "Shower seal" button. Press
> to activate. A green light will then be illuminated immediately below. On the
> intensity knob, select the desired setting. Now depress the Auto-Unsub
> activation lever. Bathe normally.
> 
> The Auto-Unsub will automatically go off after three minutes unless you
> activate the "Manual off" override switch by flipping it up. When you are
> ready to leave, press the blue "Shower seal" release button. The door will
> open and you may leave. Please remove the velcro slippers and place them in
> their container.
> 
> If you prefer the ultrasonic log-off mode, press the indicated blue button.
> When the twin panels open, pull forward by rings A & B. The knob to the left,
> just below the blue light, has three settings, low, medium or high. For
> normal use, the medium setting is suggested.
> 
> After these settings have been made, you can activate the device by switching
> to the "ON" position the clearly marked red switch. If during the
> unsubscribing operation, you wish to change the settings, place the "manual
> off" override switch in the "OFF" position. You may now make the change and
> repeat the cycle. When the green exit light goes on, you may log off and have
> lunch. Please close the door behind you.
> 


Index Nav: [Date Index] [Subject Index] [Author Index] [Thread Index]
Message Nav: [Date Prev] [Date Next] [Thread Prev] [Thread Next]